26890.
(a) Except as provided in subdivisions (b) and (c) of Section 26805, any time when the licensee is not open for business, each particular firearm shall be secured by storing the firearm in a secure facility that is part of, or that constitutes, the licensee’s business premises.(b) (1) All firearms shall also be secured using one of the following methods as to each particular firearm, unless the licensee complies with subdivision (c):
(A) Secure the firearm with a hardened steel rod or cable of at least one-eighth inch in diameter through the trigger guard of the firearm. The steel rod or cable shall be secured with a hardened steel lock that has a shackle. The lock and shackle shall be protected or shielded from the use of a boltcutter, and the rod or cable shall be anchored in a manner that prevents the removal of the firearm from the premises.
(B) Store the firearm in a locked fireproof safe or vault in the licensee’s business premises. The safe shall meet the safety standards established by the Attorney General pursuant to Section 23650.
(C) Store the firearm in a display case that is made with a steel frame that is no thinner than 12 gauge, is fitted with a hardened steel lock where the case opens to access the firearm, and that complies with one of the following:
(i) The display case is fitted with smash-proof polycarbonate panels that are at least one-quarter inch thick.
(ii) The display case is fitted with glass that is protected with a security or protective laminate film that is specifically designed to delay entry and unauthorized access, with a minimum thickness of at least 8 mils (eight-thousandths of an inch), and that includes an anchoring system on all seams of each glass panel and is also anchored to the frame.
(D) Store the firearm in a windowless room equipped with a steel security door fitted with a deadbolt lock, and that does not have a door exposed to the outside of the building.
(E) Store the firearm behind a steel roll-down door or security gate, or secure the firearm in a locked steel gun rack by use of a hardened steel bar.
(2) (A) If the licensee uses the method described in subparagraph (A) of paragraph (1), and the licensee’s location is at street level, the licensee shall install, or cause to be installed, concrete or hardened steel bollards, or other barriers, such as security planters or other devices with a similar structural integrity of bollards, to protect the location’s front entrance, any floor-to-ceiling windows, and any other doors, that could be breached by a vehicle. The bollards shall meet the following requirements:
(i) Be no less than 4 inches in diameter and 36 inches in height from the ground.
(ii) Be spaced so as not to obstruct accessible routes or accessible means of egress in compliance with Standard 206.8 of Chapter 2 of the federal Americans with Disabilities Act of 1990 (42 U.S.C. Sec. 12101 et seq.), and have a clear width of not less than 36 inches but no more than 60 inches.
(iii) Be capable of stopping a 5,000 pound vehicle traveling at 30 miles per hour, in compliance with ASTM International Standard Test Method F3016.
(B) This paragraph shall not apply to elevated loading docks, to locations of a licensee’s premises that are fitted with steel roll-down doors, or to a licensee that is unable to comply due to local ordinances, covenants, lease conditions, or similar conditions not under the control of the licensee.
(3) Bollards installed prior to September 1, 2017, shall be considered compliant with this section if they are composed of concrete or hardened steel, do not obstruct accessible routes or accessible means of egress in compliance with Standard 206.8 of Chapter 2 of the federal Americans with Disabilities Act of 1990 (42 U.S.C. Sec. 12101 et seq.), and have a clear width of not less than 36 inches but no more than 60 inches.
(c) Unless the licensee complies with subdivision (b), the licensee shall install locking steel roll-down doors on any perimeter doors and floor-to-ceiling windows. Emergency exits are exempt from this requirement where installation would be in violation of a state or local fire code.
(d) The licensing authority in an unincorporated area of a county or within a city may impose security requirements that are more strict or are at a higher standard than those specified in subdivision (a).
(e) Except as provided in subparagraph (B) of paragraph (2) of subdivision (b), upon written request from a licensee, the licensing authority may grant an exemption from compliance with the requirements of subdivision (a), (b), or (c), in any combination, if the licensee is unable to comply with those requirements because of local ordinances, covenants, lease conditions, or similar circumstances not under the control of the licensee.
(f) Subdivisions (a), (b), and (c) shall not apply to a licensee organized as a nonprofit public benefit corporation pursuant to Part 2 (commencing with Section 5110) of Division 2 of Title 1 of the Corporations Code, or as a mutual benefit corporation pursuant to Part 3 (commencing with Section 7110) of Division 2 of Title 1 of the Corporations Code, if both of the following conditions are satisfied:
(1) The nonprofit public benefit or mutual benefit corporation obtained the dealer’s license solely and exclusively to assist that corporation or local chapters of that corporation in conducting auctions or similar events at which firearms are auctioned off to fund the activities of that corporation or the local chapters of the corporation.
(2) The firearms are not handguns.
(g) This section shall become operative July 1, 2018.